User Tools

Site Tools


wiki:en:2dcam:quickstart

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
wiki:en:2dcam:quickstart [2017/01/24 10:04]
admin
wiki:en:2dcam:quickstart [2018/02/07 19:24] (current)
Line 113: Line 113:
 Now we're going to create NC-code around the outer square. Do like this: Now we're going to create NC-code around the outer square. Do like this:
  
-  * Click on the [[wiki:​en:​2dcam:​ncdatafliken|NC data tab]]+  * Click on the [[wiki:​en:​2dcam:​ncdatatab|NC data tab]]
   * Click on the [[wiki:​en:​2dcam:​mnuncg0|Rapid]] function ([[wiki:​en:​2dcam:​hotkeys|Hotkey]] **0**)   * Click on the [[wiki:​en:​2dcam:​mnuncg0|Rapid]] function ([[wiki:​en:​2dcam:​hotkeys|Hotkey]] **0**)
   * Click on the point that we drew as our start-point (X110 Y50). The point should be marked Red and if you move the mouse, a red line will follow the mouse pointer.   * Click on the point that we drew as our start-point (X110 Y50). The point should be marked Red and if you move the mouse, a red line will follow the mouse pointer.
Line 136: Line 136:
 To look at the NC-code, do like this: To look at the NC-code, do like this:
  
-  * Click on the [[wiki:​en:​2dcam:​ncdatafliken|NC data tab]]+  * Click on the [[wiki:​en:​2dcam:​ncdatatab|NC data tab]]
   * Click on the [[wiki:​en:​2dcam:​mnuncshownc|Show NC-code]] function   * Click on the [[wiki:​en:​2dcam:​mnuncshownc|Show NC-code]] function
  
Line 149: Line 149:
 We already are at a good starting point for our tool-path so we just continue as with the last square. We already are at a good starting point for our tool-path so we just continue as with the last square.
  
-  * Click on the [[wiki:​en:​2dcam:​ncdatafliken|NC data tab]]+  * Click on the [[wiki:​en:​2dcam:​ncdatatab|NC data tab]]
   * Click on the [[wiki:​en:​2dcam:​mnuncg1|Feed]] function ([[wiki:​en:​2dcam:​hotkeys|Hotkey]] **1**)   * Click on the [[wiki:​en:​2dcam:​mnuncg1|Feed]] function ([[wiki:​en:​2dcam:​hotkeys|Hotkey]] **1**)
   * Click on mid-point (Magenta) on the horizontal line that makes up an edge of the square.   * Click on mid-point (Magenta) on the horizontal line that makes up an edge of the square.
Line 167: Line 167:
 First let's move with parid to the center of the circle: First let's move with parid to the center of the circle:
  
-  * Click on the [[wiki:​en:​2dcam:​ncdatafliken|NC data tab]]+  * Click on the [[wiki:​en:​2dcam:​ncdatatab|NC data tab]]
   * Click on the [[wiki:​en:​2dcam:​mnuncg0|Rapid]] function ([[wiki:​en:​2dcam:​hotkeys|Hotkey]] **0**)   * Click on the [[wiki:​en:​2dcam:​mnuncg0|Rapid]] function ([[wiki:​en:​2dcam:​hotkeys|Hotkey]] **0**)
   * Click on the Center-point (Orange) of the circle (X50 Y50)   * Click on the Center-point (Orange) of the circle (X50 Y50)
Line 189: Line 189:
 And to look at the NC-code, do like before: And to look at the NC-code, do like before:
  
-  * Click on the [[wiki:​en:​2dcam:​ncdatafliken|NC data tab]]+  * Click on the [[wiki:​en:​2dcam:​ncdatatab|NC data tab]]
   * Click on the [[wiki:​en:​2dcam:​mnuncshownc|Show NC-code]] function   * Click on the [[wiki:​en:​2dcam:​mnuncshownc|Show NC-code]] function
  
wiki/en/2dcam/quickstart.txt · Last modified: 2018/02/07 19:24 (external edit)