This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wiki:en:2dcam:quickstart [2017/01/24 09:42] admin |
wiki:en:2dcam:quickstart [2018/02/07 19:24] (current) |
||
---|---|---|---|
Line 78: | Line 78: | ||
Now let's draw the circle with diameter 60 | Now let's draw the circle with diameter 60 | ||
- | * Click on the [[wiki: | + | * Click on the [[wiki: |
* Click on the [[wiki: | * Click on the [[wiki: | ||
* Click on Values... in the lower right corner of the screen | * Click on Values... in the lower right corner of the screen | ||
Line 94: | Line 94: | ||
==== Points ==== | ==== Points ==== | ||
- | För att kunna göra NC-banorna behöver vi visa punkter. Det görs enklast i nedre högra hörnet. | + | To be able to place our tool-path we need to make sure we display all the auto points. Fastest way to do this is to enable the points in the lower-right corner of the screen. |
- | Vi gör det enkelt för oss och aktiverar alla punkter, dvs. [[wiki: | + | We are going to make it easy for us and just enable all the points, e.i. [[wiki: |
- | Nu ska vi bara rita dit en punkt som vi vill ha som startpunkt för bearbetningen. | + | Let's draw a starting point for our tool-path. This may just be sketched, but for this introduction we'll draw a proper point. |
- | * Klicka på [[wiki: | + | * Click on the [[wiki: |
- | * Klicka på funktionen | + | * Click on the [[wiki: |
- | * Klicka på Värden... i nedre högra hörnet | + | * Click on Values... in the lower right corner of the screen |
- | * För punkten, skriv in **X110 Y50** | + | * For the point, enter **X110 Y50** |
- | Nu ska det se ut ungefär så här på skärmen: | + | At this point it should look something like this: |
{{wiki: | {{wiki: | ||
+ | ==== Outer square ==== | ||
- | ==== Yttre kvadraten ==== | + | Now we're going to create NC-code around the outer square. Do like this: |
- | Nu ska vi skapa NC-kod runt den yttre kvadraten. Gör så här: | + | * Click on the [[wiki: |
+ | * Click on the [[wiki: | ||
+ | * Click on the point that we drew as our start-point (X110 Y50). The point should be marked Red and if you move the mouse, a red line will follow the mouse pointer. | ||
- | * Klicka på [[wiki: | + | If you happend to select the wrong point you may use the [[wiki: |
- | * Klicka på funktionen [[wiki: | + | |
- | * Klicka på punkten som vi ritade ut som vår startpunkt (X110 Y50). Denna ska bli markerad Röd och rör man musen kommer en röd linje följa muspekaren. | + | |
- | Om man råkar göra fel kan man använda funktionen [[wiki:en: | + | We have just made a rapid-feed to X110 Y50. Let's continue: |
- | Vi har nu gjort en snabbmatning till X110 Y50. Nu fortsätter vi | + | |
- | | + | * Click on mid-point |
- | * Klicka på Mittpunkten | + | * Click on the upper End-point |
- | * Klicka på den övre Ändpunkten | + | * Click on the upper-left End-point (Red) on the vertical line. |
- | * Klicka på den övre-vänstra Ändpunkten | + | |
- | Fortsätt varvet runt tills du kommer fram till mittpunkten där vi startade igen. | + | Continue around the square until you get to the mid-point where we started. |
- | Nu ska det se ut ungefär så här på skärmen: | + | Remeber that if you made an error somewhere you may use the [[wiki: |
+ | |||
+ | At this point it should look something like this: | ||
{{wiki: | {{wiki: | ||
- | För att titta på NC-koden gör så här: | + | To look at the NC-code, do like this: |
- | * Klicka på [[wiki: | + | * Click on the [[wiki: |
- | * Klicka på funktionen | + | * Click on the [[wiki: |
- | Nu ska det se ut ungefär så här på skärmen: | + | At this point it should look something like this: |
{{wiki: | {{wiki: | ||
- | ==== Inre kvadraten | + | ==== Inner square |
- | Nu fortsätter vi och skapa NC-kod runt den inre kvadraten. | + | Let's continue to create tool-paths around the inner square. |
- | Snabbmatningen har vi redan gjort och vi behöver bara fortsätta att göra som förra kvadranten. | + | We already are at a good starting point for our tool-path so we just continue as with the last square. |
- | * Klicka på funktionen | + | * Click on the [[wiki: |
- | * Klicka på Mittpunkten | + | * Click on the [[wiki: |
- | * Klicka på den övre Ändpunkten | + | * Click on mid-point |
- | * Klicka på den övre-vänstra Ändpunkten | + | * Click on the upper End-point |
+ | * Click on the upper-left End-point (Red) on the vertical line. | ||
- | Fortsätt varvet runt tills du kommer fram till mittpunkten där vi startade igen. | + | Continue around the square until you get to the mid-point where we started. |
Nu ska det se ut ungefär så här på skärmen: | Nu ska det se ut ungefär så här på skärmen: | ||
- | {{wiki:en: | + | At this point it should look something like this: |
- | ==== Cirkeln | + | ==== The circle |
- | Nu har vi bara cirkeln kvar och för att göra den, gör så här: | + | Now all we have left to do is the circle. Do like this: |
- | Först ska vi förflytta oss med snabbtransport till centrum på cirkeln. | + | First let's move with parid to the center of the circle: |
- | * Klicka på [[wiki: | + | * Click on the [[wiki: |
- | * Klicka på funktionen | + | * Click on the [[wiki: |
- | * Klicka på Centrumpunkten | + | * Click on the Center-point |
- | * Klicka på funktionen Arbetsmatning | + | * Click on the [[wiki: |
- | * Klicka på nån av Kvadrantpunkterna | + | * Click on any of the Quadrant-points of the circle |
- | Nu ska det se ut ungefär så här: | + | At this point it should look something like this: |
{{wiki: | {{wiki: | ||
- | * Klicka på funktionen | + | * Click on the [[wiki: |
- | * Klicka på motstående Kvadrantpunkt | + | * Click on the opposite Quadrant-point |
- | * Välj riktning på bågen genom att förflytta muspekaren antingen till höger eller vänster om centrumpunkten. | + | * Select a direction of the arc by moving the mouse-pointer either to the left or right of the center-point. |
- | * Klicka för att välja riktning. | + | * Click to confirm the direction. |
- | * Repetera ovanstående steg för att slutföra den cirkulära rörelsen tillbaka till startpunkten. | + | * Repeat the steps above to complete the circular movement back to the start-point. |
- | Nu ska det se ut ungefär så här: | + | At this point it should look something like this: |
{{wiki: | {{wiki: | ||
- | Och vi kan titta på NC-koden genom att göra som förut: | + | And to look at the NC-code, do like before: |
- | * Klicka på [[wiki: | + | * Click on the [[wiki: |
- | * Klicka på funktionen | + | * Click on the [[wiki: |
- | Nu ska det se ut ungefär så här på skärmen: | + | At this point it should look something like this: |
{{wiki: | {{wiki: | ||
- | + | This is the end of the introduction. | |
- | Nu är vi klara med Snabbstarten. | + |